![where to buy putty in singapore where to buy putty in singapore](https://m.media-amazon.com/images/I/81WpuJGcb2L.jpg)
Ideal for repairs to timber (rotten & old), woodwork, glass with metal, stone craft, metal works, wall, architectural or hobbymolding and more Because the storage, handling andĪpplication of this material is beyond our control, we can accept no liability for the results obtained.ĭistributor for devcon in South East Asia Devcon Distributor for Singapore Devcon Distributor for Cambodia Devcon Distributor for Brunei Devcon Distributor for Cambodia Devcon Distributor for Myanmar Largest Stockist for devcon products.Multi-Porpose Waterbased Filler Interior or exterior use 100% Natural and Organic Earl's Powder Putty is perfect for interior or exterior surfaces such as wood, stone, metal, plasterboard, cement sheeting and concrete Warranty: Devcon will replace any material found to be defective.
![where to buy putty in singapore where to buy putty in singapore](https://hardwarestore.sg/wp-content/uploads/2016/07/Wessbond-Aquapatch-1-600x365.jpg)
Troweled on a vertical surface up to 6mm thick without sagging.įor complete safe and handling information, please refer to the appropriate Material Safety Data Sheets prior Of epoxy is determined by the size of the mass of epoxy and the temperature. The material wil l beįully cured in 16 hours at which time the material can be machined, drilled or painted. The exposed surface area to volume of the product should not exceed 90.6cm2/litreĪ 12mm thick section of Devcon Stainless Steel Putty will harden at 24☌ in 4 hours. To bridge large gaps or holes use fibreglass, expanded metal or Surface contact and avoid entrapping air. Putty over prepared surface with applicator (enclosed) or putty knife. Life will be longer, and above room temperature, cure and pot life will be shorter. When temperatures are below 21☌, cure and pot Stainless Steel Putty can beĪpplied when temperatures are between 13☌ and 32☌.
WHERE TO BUY PUTTY IN SINGAPORE FULL
Strongly recommended that full can units be mixed.įor best results, product should be kept and applied at room temperature. Be sure to mix material from bottom and sides of container. Mix thoroughly with a screwdriver or similar tool until a uniform, streak-freeĬonsistency is obtained, about 4 minutes. All prepared surfaces should be repaired as soon as possible, to eliminate any changes or surfaceĪdd hardener to resin.This procedure dries off any moisture, and assists theĮpoxy in achieving maximum adhesion to the substrate. Under cold working conditions, heating the repair area to 38-43☌ immediately before applying any ofĭevcon’s metal filled epoxy is recommended.Will help to remove all traces of sandblasting grit, oil, grease, dust or other foreign substances. All abrasive preparation should be followed by chemical cleaning with Devcon Cleaner Blend 300.The maximum soluble salts left on the substrate should be no more than 40 ppm A test for chloride contamination should be performed prior to anyĮpoxy application. Water blasted and left overnight to allow any salts in the metal to “sweat” to the surface, repeat blasting Metal that has been handling sea water or other salt solutions should be grit blasted and high pressure.Epoxy material must be “locked” in by defined edges and a good A 75-125 micron profile is desired for an application.ĭo not “feather edge” epoxy material. ThisĬreates increased surface area for better adhesion. An abrasive disc may be used provided white metal is revealed. All surfaces must be roughened ideally by grit blasting (8-40 mesh grit), or by grinding with a coarse.
![where to buy putty in singapore where to buy putty in singapore](https://www.lumiere32.sg/media/thumbs/74539461b909fa775acfbffca751b8ac.jpg)
All oil, grease, andĭirt must be removed before applying any epoxy material. First, degrease the surface by using anyone of Devcon Cleaner Blend 300 #19510.Proper surface preparation is essential to a successful application.